Cant access my hd idefrag6/6/2023 ![]() Other than a two pass scan there's not a lot that can be done without adding a lot of complexity, all for something that rarely happens.ĬCC is using rsync and it seems to work better.ĬCC has more serious issues. In fact, it will be a little smaller than the original since SuperDuper skips a few things that shouldn't be copied (virtual memory swap files, for instance). I did say that I've been emailing with the Developer.īut once the clone completes (which may require manually deleting a few files), it will not be bigger. It seems to me that SD! algoritm is adding files before it tries to delete files and it will therefore run into issues on drives that are close to full. CCC is using rsync and it seems to work better.Ī bug if you ask me. I did say that I've been emailing with the Developer. ![]() If it does happen, just delete a few files on the clone (which would end up being deleted anyway) to make enough space.Ī bug if you ask me. Since this issue only happens if the drive is close to full, an easier solution is just keep it not quite so full. The solution is to scan the entire drive and make list of what changed, then go through that list and delete the files that need to be deleted first (freeing up a lot of space), then go back and copy all the new/changed files. Normally there is enough room for everything to work itself out but sometimes it will start copying a new file before it deletes other files that would have created enough space for it because it hasn't seen those yet. SuperDuper scans the source drive, copying and deleting files as it goes along. The error in SD!'s logs doesn't help since all it says is that the clone drive is full. Sometime (without doing anything) I can just try to re-run the same clone operation with CCC and it works. How exactly can a clone grow to be bigger than itself? After running SD! nightly for a longer period of time the clone grows slowly until it finally errors out. I've been using SD! for years and I have pointed this out to the Developer. The error in SD!'s logs doesn't help since all it says is that the clone drive is full.įor this reason I usually reset my clones every 2-3 months. ![]() The solution is to check the SuperDuper log and see where it's running out of room and then delete some of the files on the backup drive that would get deleted anyway. This is only a problem if the drive is relatively full and can't hold both of the files. The issue with SuperDuper is that if the user deletes a large file and creates a new and different file, SuperDuper might see the new file first and try to copy it before it sees the second file and deletes it to free up space. It's a clone, not snapshots like Time Machine. ![]() The backup cannot grow larger than the original. Every now and then I will reste the SD! clone by letting it Erase and Backup. How big is the SD partition today? Is it the same size as the drive that you're cloning? SD! has a problem where the backup clone keeps growing even if it should always be the same size as the content of the drive it's cloning. However, some data may be lost, depending on which partitions change and in what direction. Works very well.ĭisk Utility can live resize too. If the BIOS menu did not recognize your SSD, you may have issues with faulty hardware or need to configure the SATA controller settings within the BIOS menu.Affect some of the partitions, depending on where the data actually is on the drive. If the SSD is listed there, you can move on and attempt the solutions mentioned below. Once in the BIOS menu, look for the Boot menu and check if the SSD is listed there. You can complete an internet search to find the correct function key to access the BIOS menu for your specific PC. The specific key required can vary for different manufacturers.įor example, on a Dell PC, you need to press the F2 key just as the Dell logo appears. To open the BIOS menu on your computer, you usually need to press the correct function key just as the computer is booting. It also controls essential tasks between the operating system and the numerous attached devices. The BIOS is the program that boots your computer. Verify That the BIOS Detects the SSDīefore we begin with the possible fixes, you want to make sure your SSD is correctly connected and is detected by the BIOS (basic input/output system). Read on to learn how to fix the SSD detection issue in Windows 10. This issue can be particularly troublesome while setting up the SSD.
0 Comments
Leave a Reply. |